5104-Hillsboro Avenue North   New Hope, MN 55428
763-531-2222








Noise and Vibration Control
Industrial Noise Control
Kinetics
Absorber Panels and Damping Material for Industrial Noise Control
Barrier, Enclosure and Curtain Systems for Industrial Noise Control
Floating Floors, Ceilings and Partitions
Shock Control or Vibration Control Systems
Vibration Isolation
Vibron
Acoustical Enclosures and Air Duct Silencers

Mueller Noise and Vibration Control Equipment Supplier Listing

Absorber Panels and Damping Material
Model S4
Kinetics Model S4 sound absorption panels Used in industrial noise control applications, Kinetics Model S4 sound absorption panels absorb low and mid-frequency sound. Model S4 damping material consists of 3 PCF glass fiber core encapsulated by a 10 mil neoprene coating, fiber glass reinforced, aluminized polyester reflective film facing.
Applications
  • Machinery enclosures
  • Engine shrouds
  • Air compressor cabinets
    		•
    Features
  • Temperature rating: -40°F to 450°F (-40°C to 232°C)
  • Good structural integrity; available in 4’ x 8’ sheets or custom die-cut shapes
  • Sound absorption rating: 1’’ board 0.75 NRC; 2’’ board 0.94 NRC
  • Flame spread rating 15, fuel contribution of 0, smoke development 10. (UL 723 test)
    Model PA
    Model PA fiber glass absorbers Kinetics Model PA fiberglass absorbers come in 4’ x 8’ sheets. Two versions are available: Model PA 410GO provides good sound absorption at mid and
    Applications
  • Interior lining of engine compartments
  • Sheet metal equipment guards
  • Equipment enclosures
  • In-plant personnel booths
    • high-frequencies and Model PA 410GB has a protective facing. The protective facing prevents shedding fibers and PA 410GB exhibits good sound absorption at low and medium frequencies.
    Features
  • Maximum temperature: Model PA 410GO 350°F (177°C); Model PA410GB 450°F (232°C)
  • Sound absorption rating: 1’’ board 0.70 NRC
  • K factor per ASTM C-177 + .230
  • Flame spread rating 15, fuel contribution of 15, smoke development 0.
    Model KFA
    Model KFA quilted face sound absorbing blankets Used in industrial noise control applications, Kinetics Model KFA quilted face sound absorbing blankets are used to reduce reflected noise. Model KFA blankets are fire safe and cleanable making it a better damping material solution than urethane foams in applications where a fire safe or cleanable product is advantageous. Model KFA quilted damping material absorbers are easily installed and have a long service life because they are unaffected by moisture, humidity, dust, dirt, oils,
    KFA Applications
  • Machinery housings
  • Building walls
  • Curtain or fixed enclosures
  • Firewalls
  • Hoods
  • Operator cabs
  • Piping and duct work
    • and most chemicals. Blankets come in 1’’ and 2’’ thickness. 2’’ thick blankets have better low frequency noise absorption capability. Blankets can be quilted on one or both sides. Depending on the applications one of three available facings is recommended. Available blanket facings include:
  • Aluminum vinyl-coated fiber glass cloth (standard)
  • High temperature silicone-coated fiber glass cloth
  • Non-maintenance non-woven porous scrim fabric
    Model KUA
    Model KUA polyester urethane foam Kinetics Model KUA is a 2 lb. per cubic foot density polyester urethane foam. Developed to have a low weight to sound absorption ratio, Model KUA absorbs reflective sound in the mid and high-frequency spectrum with peak efficiencies over 500 Hz. The foam can be provided with special facings for protection against oils, dirt, and moisture.
    Features
  • Standard thickness ¼ through 2’’ (custom thickness to 6’’ available)
  • Normal service life 10 years (depends on severity of application)
  • Sound absorption ratings: ¼ thickness 0.35 NRC; ½ thickness 0.54 NRC; 1’’ thickness 0.75 NRC; 2’’ thickness 0.90 NRC
    Model KNP
    Kinetics Model KNP panel absorbers are 2’’ thick perforated panels filled with fiber glass sound absorption material and have an aluminum or galvanized facing.
    Applications
  • Studios
  • Offices
  • Theaters
  • Computer rooms
    • Model KNP is designed to control background noise and can also be used in conjunction with existing barriers to reduce reflected noise. Features include:
  • Standard panels: 24’’ wide by 4’ to 12’
  • Colors: unfinished, grey, or white
  • Class A incombustible to federal specification (55-5118A)

    REQUEST FOR QUOTE  ||  REQUEST LITERATURE  ||  EMAIL US  ||  TOP OF PAGE

    Barrier, Enclosure and Curtain Systems
    Model A-Line
    Kinetics Model A-Line sound absorption panels have deeply contoured faces exposing eight times more surface area than flat foam panels. Standard panels are polyester polyurethane foam (not a Class A product) or melamine (Class A).
    Model A-line sound absorption panels
  • Acoustical performance: 2’’ = .90 NRC
    Applications
  • Factories
  • Data processing rooms
  • Auditoriums
  • Broadcast studios
  • Recording studios
    Model KNM
    Model KNM barriers Kinetics Model KNM barriers are used to absorb sound from piping and machinery. The Clearview versions of Model KNM sound insulate machinery without blocking an operator’s view. KNM is either draped around or suspended between equipment and quiet
    Applications
  • Pipe and duct lagging
  • Ceiling noise barriers
  • Rooftop equipment barriers
  • Noise curtain panels and enclosures
    		•
    areas. Model KNM loaded vinyl mass barrier materials are available in three formats.
  • Clearview (transparent) barrier material, non-loading and non-reinforced (KNM-50C and KNM-100C)
  • Limp barrier material non-reinforced and loaded with barium sulphate (KNM-50B and KNM-100B)
  • Limp barrier material reinforced with a fiber glass screen and loaded with barium sulphate
    Model KB-803
    Kinetics Model KB-803 sound control baffles reduce noise levels in recreational, industrial, and other high noise areas. KB-803 baffles are 2.7 pcf fiberglass with dimensions of 24’’ width x 48’’ height x 1½’’ thickness. The baffles should be installed near the source of the noise and can be suspended by wire. Model KB-803 baffles can reduce the noise in a room by up to 10 dB depending on the room’s configuration. Versions of Model KB-803 are available to meet FDA and USDA approved requirements.
    Model KNC
    The Kinetics Model KNC is a noise control curtain that can be used to create partial or full enclosures. Curtains are available in a limp mass vinyl format or vinyl quilted fiberglass format. The curtains act as movable barriers between noisy and quiet areas.
    Applications
  • Punch press enclosures
  • Compressor enclosures
  • Pump enclosures
    • Model KNC curtains incorporate a self-supporting track making setting up entrances and exits easy. The curtains oil and chemical resistance make them well suited for tough industrial applications. Features include:
  • ½ to 2½ psf surface weight
  • Sound reduction to 29 dB
  • Panels come with grommets at the top and Velcro along the entire length of each edge

    REQUEST FOR QUOTE  ||  REQUEST LITERATURE  ||  EMAIL US  ||  TOP OF PAGE

    Floating Floors, Ceilings and Partitions
    Model RIM
    Kinetics Model RIM is a 2’’ thick precompressed molded fiberglass isolation pads and is used to produce a floating concrete floor. The pad Model RIM floating floorare set in a ½'' thick pouring form. A concrete floor meeting sound transmission class of STC 73 can be achieved using this system. The material is provided in 4’ rolls 50’ long and 1.5’’ thick. Applications include:
  • Mechanical equipment noise control
  • Loud musical instruments
  • Industrial noise
    Model KIP
    Kinetics Model KIP fiber glass isolators can be used in floating concrete floors or as a vibration isolator. KIP isolators are a high density matrix of precompressed molded glass fibers, individually coated with a flexible water-resistant membrane. An advantage compared to other floating concrete floor materials is KIP isolators provide unprecedented design freedom. Features include:
  • Inorganic fiber glass media
  • Constant natural frequency in wide load range
  • Predictable dynamic response
  • Controlled viscous damping
  • Load capacities 1 psi to 500 psi (0.07 to 35 kg per kg/cm2)
  • Applied loads are less than precompression loads thus providing 300% or more overload safety factor
  • Non-corrosive, non-combustible, non-absorbent and resists rust, ozone, mildew and fungus
  • Media characteristics are constant between –40°F and 250°F (4°C to 121°C)
    Spring Liftslab Floating Floor
    Kinetics Liftslab Floating Floors control low frequency impact and airborne noise. Standard systems come with 2’’ deflection springs. Custom systems are available. Liftslab floating floors are used to isolate sensitive equipment from transient building noise. Applications include gymnasium floors and metrology room floors.

    REQUEST FOR QUOTE  ||  REQUEST LITERATURE  ||  EMAIL US  ||  TOP OF PAGE

    Shock Control or Vibration Control Systems
    Model NDF
    Kinetics Model NDF isolation pads are constructed from laminated neoprene and cotton duck fabric. NDF pads have 64 layers of laminated neoprene and cotton duck fabric in each pad (2.6 layers per mm). Features include:
  • Intermittent loading to 10,000 psi
  • Allowable shock loading 2000 psi
  • Temperature range –35° to 200°F (-37°C – 93°C)
  • Conforms to MIL-C-882B
  • Resistant to water, brine, fungus, and bacterial growth. SAE 30 oil only slight swelling

    REQUEST FOR QUOTE  ||  REQUEST LITERATURE  ||  EMAIL US  ||  TOP OF PAGE

    Vibration Isolation
    Model SL
    Model SL housed spring isolators Kinetics Model SL housed spring isolators are stabile springs assembled into telescoping cast iron or aluminum housings. Specifications include:
  • Deflections up to 1.84 (varies depending on spring type selected)
  • Load capacities: 35 to 3500 lbs. (varies depending on spring type selected)
  • Springs have lateral stiffness greater than 1.0 times the rated vertical stiffness and a minimum of 50% overload capacity
  • 1,000 hour salt spray rating per ASTM B-117
  • Recommended to isolate lightweight mechanical equipment with low operating speeds (1200 rpm or lower)
    Model SM
    Kinetics Model SM housed spring isolators are stabile springs assembled into telescoping cast iron or aluminum housings. Specifications include:
  • Deflections up to 1.79 (varies depending on spring type selected)
  • Load capacities: 250 to 5900 lbs. (varies depending on spring type selected)
  • Springs have lateral stiffness greater than 1.0 times the rated vertical stiffness and a minimum of 50% overload capacity
  • 1,000 hour salt spray rating per ASTM B-117
  • Recommended for isolating vibration produced by industrial and process machinery where more damping is required and less motion can be tolerated
    Model FLS-1 and FLS-2
    Model FLS restrained spring isolators Kinetics Model FLS restrained spring isolators are free-standing, large diameter, laterally stable springs assembled into welded steel housings. FLS springs are designed to limit the vertical movement of the equipment if equipment forces are changed. Specifications include:
  • Deflections up to 2.03 (varies depending on spring type selected)
  • Load capacities to 15,600 lbs. (varies depending on spring type selected)
  • Springs have lateral stiffness greater than 1.0 times the rated vertical stiffness and a minimum of 50% overload capacity
  • 1,000 hour salt spray rating per ASTM B-117
  • Recommended for large fluid carrying equipment including: boilers, cooling towers, and chillers
    Model FDS
    Kinetics Model FDS free-standing spring isolators are free-standing, unhoused, large diameter, laterally stabile, steel springs assembled into an upper load plate and leveling assembly.Model FDS free-standing spring isolators To ensure stability the springs have lateral spring stiffness greater than 1.0 times the rated vertical stiffness. Specifications include:
  • Deflections up to 4’’ (varies depending on spring type selected)
  • Load capacities to 23,200 lbs. (varies depending on spring type selected)
  • Springs have lateral stiffness greater than 1.0 times the rated vertical stiffness and a minimum of 50% overload capacity
  • 1,000 hour salt spray rating per ASTM B-117
  • Recommended for stopping noise transmission from large equipment into the floor and thus the rest of the building
    Model FHS
    Kinetics Model FHS seismic control spring isolators are a Model FDS spring with a steel housing to limitModel FHS seismic control springs both lateral and vertical movement. Depending on the load and seismic zone, an optional steel load spreader plate to distribute the load among concrete anchors may be added. Specifications include:
  • All direction restraint with vertical stops
  • Same free and operating height
  • Motion limitation 0.2’’ in all directions
    Model FLSS
    Kinetics Model FLSS restrained spring isolators are free standing, large diameter, laterally stabile, steel springs assembled into weight into welded steel housing assemblies. Specifications include: Model FLSS restrained spring isolators
  • Springs have lateral stiffness greater than 1.2 times the rated vertical stiffness and a minimum of 50% overload capacity
  • Deflections up to 4’’ (varies depending on spring type selected)
  • Load capacities to 11,800 lbs. (varies depending on spring type selected)

    REQUEST FOR QUOTE  ||  REQUEST LITERATURE  ||  EMAIL US  ||  TOP OF PAGE

    Acoustical Enclosures and Air Duct Silencers
    Acoustical Enclosures
    Vibron acoustical enclosures use Noiseblock STL and HTL panels. The panels are filled with 2.5 pcf glass fiber or wool sound proofing material. The skin is galvanized steel. Enclosures are available with doors, access panels, and ventilation packages.acoustical enclosure
  • Acoustical doors: heavy duty hardware and seals to stop noise leakage
  • Windows: ¼'' laminated safety glass with double or single glaze framing and sealing included
  • Removable panels for access to equipment can be incorporated into the enclosures design
  • Ventilation systems: intake and exhaust silencers and a supply or exhaust fan are provided. Designed to meet applications airflow requirements
    Silencers
    circular silencerVibron silencers are available in circular and rectangular format. Silencers stop airborne noise from transmitting through HVAC ducts and equipment. Silencers due effect air flow, so their implementation needs to be carefully considered. Applications include, loud manufacturing and other noisy environments.

    REQUEST FOR QUOTE  ||  REQUEST LITERATURE  ||  EMAIL US  ||  TOP OF PAGE

    		•














    Home |  Product Catalog |  Company Info |  Market Info |  Career Opportunities |  Contact Us |  Help | User Agreement